NIRCam Coronagraphic Imaging APT Template
Main article: NIRCam Coronagraphic Imaging
See also: HCI Roadmap, HCI APT Instructions, NIRCam Coronagraphic Imaging Recommended Strategies, NIRCam and MIRI Coronagraphy of HR8799 b, NIRCam and MIRI Coronagraphy of the Beta Pictoris Debris Disk
Coronagraphic imaging is one of 5 observing modes available with the Near Infrared Camera (NIRCam). NIRCam offers 5 coronagraphic occulting masks in the focal plane and 2 Lyot stops in the pupil plane. One Lyot stop is used with the round coronagraphic masks, and the other Lyot stop is used with the bar-shaped coronagraphic masks. NIRCam's 3 round coronagraphic masks, MASK210R, MASK335R, and MASK430R, have inner working angles IWA = 0.40", 0.63", and 0.81" (radius), corresponding to 6λ/D at 2.1, 3.35 and 4.1 μm. The 2 bar-shaped coronagraphic masks, MASKSWB and MASKLWB, are tapered, with IWA varying by a factor of 3 along their lengths. The half widths at half maximum (HWHM) at the bar end points for the short wavelength (SW) occulter MASKSWB are 0.13" and 0.39", whereas for the long wavelength (LW) occulter MASKLWB are 0.29" and 0.87".
The observer will have control over 3 primary parameters for NIRCam coronagraphic imaging:
- coronagraphic mask + filter combination
- small grid-dithering type
- detector read out pattern and exposure time (via the number of groups and integrations).
Allowed values are documented in the NIRCam Coronagraphic Imaging Template parameters.
Step-by-Step APT instructions
The following parameters are generic to all templates, and are not discussed in this article: observation Label, observations Comments, , ETC Wkbk. Calc ID (in the Filters dialog box),Mosaic Properties, and .
Mosaics are not available for NIRCam coronagraphic imaging.
Main article: NIRCam Modules
NIRCam coronagraphic imaging is available only using Module A, with Module B as a back-up. This parameter is not user changeable.
Main article: NIRCam Coronagraphic Occulting Masks and Lyot Stops
The user specifies the coronagraphic mask, depending on the target-host separation, necessary contrast, and desired filter. Selection of the coronagraphic mask determines also the Acq Filter parameter and the Target Acquisition Subarray. The available coronagraphic masks are: MASK210R, MASKSWB, MASK335R, MASK430R, MASKLWB.
Target Acquisition parameters
Target Acquisition is required for coronagraphic imaging. This section specifies the Target ACQ and Acq Exposure Time.
The user specifies the Acq Target and the Acq Target Brightness.
The Acq Filter is determined by the choice of the coronagraphic mask and it is not user changeable (F210M for the SW occulters MASK210R and MASKSWB, and F335M for the LW occulters MASK335R, MASK430R, and MASKLWB).
The selected Acq Target may be either the same as the science target or any other target defined in the APT file.
Acq Target Brightness
The user selects the Acq Target Brightness parameter as a function of the target magnitude in the Acq Filter. If BRIGHT is chosen, the target will be imaged through a neutral density (ND) square. BRIGHT should be used for targets with magnitudes brighter than approximately 8.2 mag (F210M) and 6.8 mag (F335M).
Acq exposure time
Main article: Understanding JWST Exposure Times
A Target ACQ must be completed by selecting a MULTIACCUM exposure configuration. Each exposure is configured by setting the readout pattern and characteristic parameters: Acq Readout Pattern and Acq Groups per Integration.
All nine NIRCam readout patterns are available for the Target Acquistion: RAPID, BRIGHT1, BRIGHT2, SHALLOW2, SHALLOW4, MEDIUM2, MEDIUM8, DEEP2, DEEP8.
Acq Groups per Integration
Acq Groups/Int defines the number of groups during an integration. The user can select one of the following options: 3, 5, 9, 17, 33, 65.
Note that Target ACQ images are taken using the 1282 (SW) or 642 (LW) subarray. For this reason, the number of groups per integration is not limited to 10 as in the Astrometric Confirmation Image and Science Exposure.
Acq Integrations/Exp, Acq Total Integrations, and Acq Total Exposure Time are not user changeable. For Target ACQ, Acq Integrations/Exp is always 1.
Astrometric confirmation image parameters
Obtain astrometric confirmation images?
If Yes is selected, confirmation images are taken. These are two identical exposures using 1 SW SCA ( A2 for the occulter MASK210R, A4 for the occulter MASKSWB), or one LW SCA (A5 for all the LW occulters). Images are taken before and after the science exposures. The first one is taken before and the second taken after the pointing adjustment that moves the target from the target acquisition position to the location behind the selected coronagraphic mask. The filter for confirmation images is the same as the target acquistion filter in Acq Filter. (F210M for SW and F335M for LW).
Conf. exposure time
The user configures the Astrometric Confirmation Image exposure time by setting the following parameters: Conf. Readout Pattern, Conf. Groups/Int, Conf. Integrations/Exp. The maximum number of groups per integration is 10. The resulting exposure time is displayed in Conf. Total Exposure Time. Conf. Total Dithers and Conf. Total Integration are not user changeable. For the Astrometric Confirmation Image Conf. Total Dithers is always 1.
Main article: NIRCam Detector Subarrays
NIRCam coronagraphic imaging supports observations using the full-frame or a subarray on a single detector. Subarrays reduce data volumes and readout times, enabling rapid observations of bright objects without saturation. If one of the SW masks is being used, data will be collected using the the appropriate SW detector. If one of the LW masks is being used, data will be collected on the LW detector. Choices for the SUBARRAY parameter are: FULL, SUB640 (for the SW channel), and SUB320 (for the LW channel).
Table 1. NIRCam coronagraphic imaging array and subarray properties
Size in pixels
Nrows × Ncolumns
FOV (each side)
FOV (each side)
|FULL||2048 × 2048||63"||129"||10.73676||4|
|SUB640||640 × 640||20"||4.18584||1|
|SUB320||320 × 320||20"||1.06904||1|
NIRCam coronagraphic imaging supports various small-grid dithers. DITHER PATTERN values available for the round shaped coronagraphic masks (MASK210R, MASK335R, and MASK430R) are:
Table 2. Dither patterns for round shaped coronagraphic masks (MASK210R, MASK335R, and MASK430R)
Number of dithers
DITHER PATTERN values available for the bar-shaped coronagraphic masks (MASKSWB, MASKLWB) are:
Table 3. Dither patterns for bar-shaped coronagraphic masks (MASKSWB, MASKLWB)
|Dither Type||Number of dithers|
Filters and exposures
The user specifies the Filter for the scientific observations. Available filters are a function of the chosen coronagraphic mask. The scientific exposure is configured by setting the readout patterns and characteristic parameters: Readout Pattern, Groups/Int, and Integrations/Exp. Groups/Int is limited to 10 for all readout patterns except DEEP2 and DEEP8, which allow up to 20.
Total Dithers and Total Integrations are not user changeable and they reflect the values selected in the Dither Pattern and Integrations/Exp fields.
The resulting exposure time for each filter is displayed in Total Exposure Time.
PSF reference observations
Main article: NIRCam Detector Subarrays
In most cases, three or more coronagraphic observations should be defined to support PSF subtraction:
- Science observation #1
- Science observation #2 with the telescope rotated by a specified offset
- PSF reference star
For a detailed description of the observational strategies, see the Coronagraphic Sequences page.
This is a PSF reference observation
Checking this box designates the observation as a PSF reference star used for PSF subtraction (A detailed discussion on the choice of a good PSF reference star can be found in the High Contrast Imaging pages.) The observation for a PSF reference star should mirror the observation for the user's science target. Note reference star observations have no proprietary period.
PSF reference observations
If this observation is of a science target, then use this field to associate it with an appropriate PSF reference observation (based on those that have been defined elsewhere in the observing proposal).
In case the user does not need any PSF Reference Observations (e.g. for a survey of many targets, some of the science targets may serve as PSF references for one another), they must check this box and explain with additional text in the science justification section of a submitted proposal the absence of PSF Reference Observations in APT.